Request a Thin Pour Sample

Thin PourReprorubber® Thin Pour

Reprorubber® Thin Pour is a two component, addition cured, platinum catalyzed, hydrophobic vinyl polysiloxane. Its two components are poured into a container and mixed to obtain a uniform mixture. It may be used to reproduce surface characteristics. It is able to reproduce surfaces down to submicron particles or scratches. It is cured at room temperature. However, warmer temperatures accelerate the setting time and cooler temperatures slow the setting time.

Final Color: Light Green

Further information on composition is available on MSDS.

Physical Properties Information

Available Products

Trial Size Kit

#16116 - Thin Pour 130ml Trial Kit - Details | Buy Now

Standard Size Kits

#16135 - Thin Pour 380ml Kit - Details | Buy Now
#16137 - Case of 10 380ml Kits - Details | Buy Now

Cartridge System Kit

#16300 - Thin Pour Green Quick Dispense Cartridge System Kit Complete - Details | Buy Now

Thin Pour Physical Properties

Determined at 23°C (72°F) (Tested according to ISO 4823)

Base Paste

Appearance -
Homogenous blue-colored runny paste, Filling loading approximately 25% silicon dioxide.

Catalyst Paste

Appearance -
Homogeneous, yellow-colored runny paste, Filling loading approximately 25% silicon dioxide.

Mixed Material

Appearance -
Homogenous green-colored runny paste

Mixing Time

  • 30 seconds, Larger masses may take up to 60 seconds.
  • Working Time (prior to gellation) – 4.0 – 4.5 minutes

Setting Time

8 – 9 minutes. Varies with ambient temperature. Warmer temperatures accelerate the setting time. Cooler Temperatures slow the setting time.

Compression Set (Recovery from deformation)

0.5%

Strain in Compression (A modified Modulus of Elasticity)

6 – 7%

Shore A30

Dimensional Change

  • After 24 hours –0.50 % Change (negative 0.50% change) this means it shrinks 0.50%
  • After 7 Days –0.50 % Change (negative 0.50 % change) this means it shrinks 0.50%

Tear Strength

200 psi

Flash Point of the polymers used

130°C (266°F)

Ignition Temperature of the polymers used

470°C (878°F)

Fully set material may be autoclaved, but its dimensional stability may be compromised. If allowed to return to room temperature, should return to original shape.

Disinfection

Since material is hydrophobic, immersion in disinfectants is acceptable. The surface color may change due to the disinfectants used.

Back to Product ^

For Reprorubber® Thin Pour Users

Repro-Mix™ II Dispensing Gun System

A mixing and dispensing system that enables you to make quick and accurate reprorubber replicas, without manual mixing and fuss!

Repro-Mix

Repro-Mix™ II System consists of the following:

  • 50ml dual barrel syringe with reusable end cap; easily filled by pouring contents of Reprorubber® into cartridge barrels.
  • Disposable low cost Helix Mixing Nozzle Tips easily attach to and detach from dual barrel syringe.
  • REPRO-MIX™ II Dispensing Gun.

Available Products

Repro-Mix™ II Kit

#16300 - Complete Repro-Mix™ II Kit - Details | Buy Now

Consisting of 1 each Repro-Mix™ II Dispensing Gun, 6 each 50ml prefilled Reprorubber Disposable Cartridges, 15 each Disposable Mixing Nozzles, deluxe fitted carrying case, and complete instructions for usage.

Replacement Items

#16301 - Reprorubber Thin Pour (Green) 50ml Cartridge, 1 each - Details | Buy Now
#16302 - Reprorubber Thin Pour (Green) 50ml Cartridges, 6 pack - Details | Buy Now
#16311 - Repro-Mix II Dispensing Gun (reusable) - Details | Buy Now
#16313 - Repro-Mix II Helix Mixing Nozzles, 15 Pack - Details | Buy Now
#16316 - Repro-Mix II Helix Mixing Nozzles, 100 Pack - Details | Buy Now
#16314 - Micro Injector Nozzle, Pack of 15 - Details | Buy Now
#16315 - Quick Dispense Cartridge System Fitted Case (without contents) -
Details | Buy Now

Applications

You can take impressions of:

Other Uses Include:

Thin Pour ApplicationsThin Pour Applications

Request a Thin Pour Sample

View All Products at Flexbar.com